Skip to main content
Teltonika routers and IoT gateways

Teltonika routers and gateways: a link that holds in the field

A solar park without fibre, a machine on the shop floor, a vehicle on the road: Teltonika routers and IoT gateways bring 4G/5G to places where no cable runs, and stay reachable remotely via RMS. Ascend supplies the right hardware preconfigured, with SIM and round-the-clock support.

Teltonika routers and gateways: a link that holds in the field (AI-generated video)
More about our AI labelling

The principle at a glance

Teltonika router in the field: machine or site, Teltonika router or gateway with dual-SIM failover, 4G/5G mobile network with VPN tunnel, RMS remote management, your team with Ascend support 24×7

At the site, a Teltonika router or gateway sits on the DIN rail and connects a machine, camera or controller via Ethernet, RS232/RS485 or digital I/O. Two SIM cards make sure the second one takes over automatically if one network fails. A VPN tunnel carries the traffic to your head office, and through the Teltonika Remote Management System (RMS) you can see and configure every device without it needing a public IP address.

What goes wrong in the field, and what Teltonika does about it

Industrial connectivity rarely fails because of bandwidth. It fails because of a network outage, a technician who has to travel far for every fault, or a device that cannot take the heat inside a control cabinet.

A network goes down

Dual SIM with automatic failover: if the first mobile network drops, the second SIM takes over, and the router returns to the primary connection by itself once the fault is cleared.

Nobody is on site

With RMS you check status, change configurations and roll out firmware remotely, even if the device sits behind a private mobile IP address.

Heat and cold in the control cabinet

Aluminium housing on the RUTX11 and RUTX50, DIN rail mounting and operating temperatures from -40 °C to 75 °C on the RUTX11, RUTX50, TRB245 and TSW212.

The machine speaks Modbus

RutOS comes with Modbus, MQTT, DNP3 and OPC UA; TRB gateways connect controllers directly via RS232/RS485 and digital inputs and outputs.

Data must be encrypted

WireGuard, IPsec, OpenVPN and ZeroTier run directly on the router, with WPA3 for Wi-Fi. The tunnel is up before the first application speaks.

Three suppliers, no single contact

Ascend delivers the router, SIM, RMS licence and preconfiguration from a single source and looks after operations with 24×7 support.

Which Teltonika family fits your site?

Typical useMobile network and interfacesExample model
RUT2xx: compact 4G routersSmall sites, kiosks, checkouts, backup for a DSL line4G LTE Cat 4, 2 Ethernet ports, Wi-Fi 4, digital inputs/outputs, automatic WAN failoverRUT241
RUT9xx: dual-SIM industrial routersMachines and plants with a serial connection4G LTE, dual SIM with auto-failover, RS232/RS485, GNSS (RUT956)RUT951, RUT956
RUTX: gigabit routers from LTE Cat 6 to 5GSites with many end devices, vehicles, railRUTX11: LTE Cat 6 up to 300 Mbit/s, 4x gigabit, Wi-Fi 5, GNSS, EN 45545-2; RUTX50: 5G SA/NSA up to 3.3 Gbit/s, 5x gigabit, eSIM variantRUTX11, RUTX14, RUTX50
RUTM: 5G for critical sitesBusiness-critical sites, two networks at the same timeRUTM52 with two 5G modems, 5x gigabit, Wi-Fi 5, Modbus, DLMS, DNP3, OPC UA (on request)RUTM50, RUTM52
TRB: IoT gatewaysA single machine, meter, controller, cameraTRB245: LTE Cat 4, digital I/O, RS232/RS485, GNSS, Modbus TCP/RTU; TRB501: 5G / LTE Cat 19 with digital I/O, USB and PoE inTRB245, TRB501
TSW: industrial switchesControl cabinet, factory hall, fibre uplinkTSW212: 8x gigabit plus 2 SFP, managed, Profinet Class B; TSW202: managed PoE+ with SFP; TSW200: unmanaged PoE+TSW212, TSW202, TSW200

RMS rollout in five steps

  1. 1
    Clarify requirementsWe ask about sites, applications, data volume and whether a machine needs to be connected via Modbus, RS485 or digital I/O.
  2. 2
    Choose family and modelFrom RUT, RUTX, RUTM, TRB and TSW we pick the model that fits network coverage, port requirements and environment, and check availability in the shop.
  3. 3
    Preconfiguration at AscendOur technicians set up RutOS, SIM profiles, failover rules and VPN tunnels. On request, we also register the devices in your RMS account.
  4. 4
    Shipping and installationThe router arrives ready to use with a SIM. On site, all you need is a DIN rail, an antenna and power; the tunnel builds itself.
  5. 5
    Operation via RMSYou manage status, configuration and firmware of all devices centrally in RMS. Ascend supports operations with 24×7 support.

Why Teltonika routers hold up in the field

Teltonika Networks builds routers, gateways, access points and switches for environments where office hardware gives up after its first summer in a control cabinet. All devices run RutOS, a Linux system based on OpenWrt. Anyone who can configure a RUT241 will feel at home on a RUTX50 or a TRB245, because firewall, failover and VPN are named the same everywhere.

The RUTX11 shows what the family is about: LTE Cat 6 with up to 300 Mbit/s, two SIM slots with automatic switchover, four gigabit Ethernet ports, dual-band Wi-Fi 5, GNSS for position and time synchronisation, operation from -40 °C to 75 °C on 9 to 50 V DC. On top of that comes rail certification to EN 45545-2. The RUTX50 lifts this to 5G with SA and NSA architecture, up to 3.3 Gbit/s downlink and five gigabit ports; in the Ascend Shop we also carry it as an eSIM variant.

For small sites the compact RUT241 is often enough: 4G LTE Cat 4, two Ethernet ports, Wi-Fi 4, digital inputs and outputs and automatic WAN failover. It is the all-rounder when a shop, a kiosk or a building site needs to get online quickly and reliably, also as a backup for an existing fixed-line connection.

RMS: remote management without a public IP address

Mobile connections usually have no public IP address. Without further measures, a router in the field is therefore unreachable as soon as something goes wrong. The Teltonika Remote Management System solves this by having the device establish the connection to the RMS platform itself. You see all routers, gateways and switches in a single interface, read signal values and data usage, change configurations, roll out firmware to many devices at once and reach devices behind the router via remote access.

RMS is licensed by points: one point equals one device for one month. A prepaid licence with 1,800 points therefore covers, for example, 50 devices for 36 months. You get the points through Ascend's 802.Cloud licence shop; we also carry the prepaid licence with 1,800 points as an item in the Ascend Shop. On request, we register new devices in your RMS account before shipping, so they appear in the overview right after power-up.

Typical fields of use

Energy and solar parks. Inverters, meters and cameras at remote sites report their data through a Teltonika router or a TRB gateway; Modbus TCP and MQTT run directly on the device. How we connect solar parks with 5G and Starlink is described on the page Internet for solar parks.

Vehicles, rail and mobile deployments. The RUTX11 and RUTX50 provide GNSS position and Wi-Fi in the vehicle; the RUTX11 is certified to EN 45545-2 for rail vehicles, the ATRM50 to EN 50155 and EN 45545-2 with M12 connectors. More under Wi-Fi for vehicles and Mobile router.

Industry and automation. The TRB245 and TRB501 connect a single controller via RS232/RS485 and digital inputs and outputs; the TSW212 distributes inside the control cabinet with Profinet Class B and two SFP uplinks for fibre.

Backup and site networking. As a second WAN path alongside DSL or fibre, a Teltonika router keeps checkouts, telephony and VPN alive when the line fails. For bonding several connections into one highly available line, we rely on Bondix or Peplink.

What Ascend takes care of for you

Ascend has been a systems house in Nuremberg since 2010 and distributes Teltonika Networks alongside Peplink, Bondix and Ekahau. We do not sell boxes, we sell working connections: you get the router with the SIM inserted, failover rules set up and a VPN tunnel; we handle the registration in your RMS account on request. What remains on site is mounting on the DIN rail.

With the hardware, we can supply the matching Ascend router SIM, which automatically registers in Germany with the network offering the best reception, applies at the same price across the EU and can be cancelled monthly. Antennas, power supplies and mounting kits for every Teltonika family are available in the shop.

Our support is available 24×7. If a site goes down, our technicians look at RMS first before anyone gets in a car. All prices in the shop are net; our offers are aimed at business customers.

Note: TRB500 is discontinued, the TRB501 takes over

Teltonika moved the 5G gateway TRB500 into the end-of-life phase on 3 November 2025; orders were accepted until 3 May 2026, and support runs until November 2031. The successor is the TRB501 with 2.5 Gbit/s Ethernet, 512 MB RAM and eSIM. For new projects we therefore plan with the TRB501; existing TRB500 installations we continue to support.

Matching products

Frequently asked questions about Teltonika routers and gateways

Ready for a connection that holds up in the field?

Send us your sites, applications and the number of devices you want. We recommend the right Teltonika family, preconfigure it and deliver with SIM and RMS licence.

Discuss your Teltonika project

Briefly describe your plan: sites, application, number of devices, requirements for failover or remote management. You get a concrete recommendation, not a brochure. Free of charge and without obligation.

We usually reply within one business day · we never share your data